BleepingComputer.com: Finding configuration IP address for a switch

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Finding configuration IP address for a switch I need some thoughts on how to find out the config ip for a switch

#1 User is offline   RoderickUsher 

  • New Member
  • Pip
  • Find Topics
  • Group: Members
  • Posts: 2
  • Joined: 30-June 10

Posted 30 June 2010 - 05:53 PM

Hi everyone :thumbsup:

Ok. I have a CISCO Catalyst Express 500G switch on my network. The person who set the network up (before I was here) neglected to make note of the configuration IP for it. That wasn't a problem until now (I need to change a setting on the switch). I have NO idea how to find it out. I have:

checked the arp logs of several computers.
looked in the DHCP list (its not there so I'm assuming it was statically assigned)
manually tried all the addresses in the block we use (192.168.1.1-254)
The stupid 500G doesn't have a console port
I dont want to erase all the settings (because I dont know what they are!)

I have the MAC address but that seems to be less helpful then I thought it would be (RARP requesting doesnt seem to be an option)

How do I find out the config IP address for the stupid switch!

Thank you all SO MUCH in advance for your help -- really banging my head against the wall on this one.

#2 User is offline   Chuck229 

  • New Member
  • Pip
  • Find Topics
  • Group: Members
  • Posts: 2
  • Joined: 28-June 10

Posted 30 June 2010 - 10:19 PM

I think it usually the same as your default gateway address.

From a cmd prompt type -> ipconfig <enter>

From a web browser enter the ip address of your Default Gateway.

This post has been edited by Chuck229: 30 June 2010 - 10:20 PM


#3 User is offline   RoderickUsher 

  • New Member
  • Pip
  • Find Topics
  • Group: Members
  • Posts: 2
  • Joined: 30-June 10

Posted 01 July 2010 - 01:38 PM

Thanks for the suggestion Chuck. THe default gateway is not the switch, however. The default gateway is the router. Switches are layer 2 devices -- the IP address is ONLY for management purposes, hence why it isn't ever cropping up in ARP tables, nothing looks for it. Traffic doesn't consider the switch to be a stop (hence why tracert wont show it).


View PostChuck229, on Jun 30 2010, 11:19 PM, said:

I think it usually the same as your default gateway address.

From a cmd prompt type -> ipconfig <enter>

From a web browser enter the ip address of your Default Gateway.


#4 User is offline   Retirednow 

  • Member
  • PipPip
  • Find Topics
  • Group: Members
  • Posts: 120
  • Joined: 07-October 09

Posted 02 July 2010 - 01:53 AM


#5 User is offline   Lisa Junior 

  • New Member
  • Pip
  • Find Topics
  • Group: Members
  • Posts: 4
  • Joined: 07-July 10

Posted 07 July 2010 - 02:57 AM

Hi, I think in this case, you just need a MAC scanner, which may be very helpufl. Install it on your computer and start scanning, you can get a list.

#6 User is offline   kennzsniper 

  • Member
  • PipPip
  • Find Topics
  • Group: Members
  • Posts: 142
  • Joined: 25-March 10
  • Gender:Male

Posted 07 July 2010 - 04:20 PM

RARP would be your route here. Lisa suggestion is quite good. You need to try it to acquire the IP address of the manageable switch.
Hardware tech when I was in college.
1st job was a network support for SOHO
2nd job was lappy tech
3rd Job way out of my league but its nice...

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users