Hello everyone.
A few days ago, I found that my computer was crashing from overheating. After opening up the case for cleaning, I discovered that the case fan became unplugged. So I plug it back in.
Now the temperature levels are great, but, that fan is always running at maximum speed, making a really loud noise. I'm pretty sure that before it had a variable speed. SpeedFan is unable to read my fan speeds.
The fan, when I hold it with my hand in the air, makes an acceptable noise level. Though, when it's attached to the case, it's much louder, I think because of the vibrations against the case. I tried putting rubber between where the fan contacts the side of the case, but it didn't help much.
Any suggestions?
Thanks,
The Panda
Page 1 of 1
Fan Really Loud
#1
Posted 18 August 2009 - 08:36 AM
#2
Posted 18 August 2009 - 09:29 AM
Hi PropagandaPanda!
Could it read the readings before this problem happened?
You've got two options here (apart from changing the fan):
1. Your first option would be to try and ensure the fan is tightly secured to the case. You can do this by getting holders for your fan. Depending on your computer case, there should be slots where you'd need to secure the holder to the case using a screw.
2. Your second option would be, instead of using rubber, try using a piece of sponge. It should be able to dampen the vibrations caused by the fan.
Edit: Just had another idea:
Instead of just using rubber, insert a layer of sponge in between the fan and the rubber. Reason why I'd use sponge is that it is really good at dampening forces transferred between the fan at the case.
Hope that helps
Quote
SpeedFan is unable to read my fan speeds.
Could it read the readings before this problem happened?
You've got two options here (apart from changing the fan):
1. Your first option would be to try and ensure the fan is tightly secured to the case. You can do this by getting holders for your fan. Depending on your computer case, there should be slots where you'd need to secure the holder to the case using a screw.
2. Your second option would be, instead of using rubber, try using a piece of sponge. It should be able to dampen the vibrations caused by the fan.
Edit: Just had another idea:
Instead of just using rubber, insert a layer of sponge in between the fan and the rubber. Reason why I'd use sponge is that it is really good at dampening forces transferred between the fan at the case.
Hope that helps
This post has been edited by aommaster: 18 August 2009 - 09:31 AM
My website: http://www.aommaster.com

Please do not send me PM's requesting for help. The forums are there for a reason : )
If I am helping you and do not respond to your thread for 48 hours, please send me a PM
All my help is free. However, if you would like to make a donation, then please click here.

Please do not send me PM's requesting for help. The forums are there for a reason : )
If I am helping you and do not respond to your thread for 48 hours, please send me a PM
All my help is free. However, if you would like to make a donation, then please click here.
#3
Posted 18 August 2009 - 10:21 AM
Hello. Thanks for the reply.
I don't think so, no.
I'll try putting in the sponge later today and see how it goes.
With Regards,
The Panda
Quote
Could it read the readings before this problem happened?
I'll try putting in the sponge later today and see how it goes.
With Regards,
The Panda
#4
Posted 18 August 2009 - 11:00 AM
It just might be time to replace it...case fans are cheap and readily available.
As for attaching, I just attach mine with superglue or a reasonable substitute
.
Louis
As for attaching, I just attach mine with superglue or a reasonable substitute
Louis
#5
Posted 18 August 2009 - 11:13 AM
At a second look, most of the noise if from the air moving through the grill.
Guess there's not much to do about that, apart from cutting it off.
The Panda
Guess there's not much to do about that, apart from cutting it off.
The Panda
Share this topic:
Page 1 of 1

Help



Back to top









