BLEEPINGCOMPUTER NEEDS YOUR HELP!
BleepingComputer is being sued by Enigma Software because of a negative review of SpyHunter.
A case like this could easily cost hundreds of thousands of dollars. If we have ever helped you in the past, please consider helping us. To learn more and to read the lawsuit, click here.
CONTRIBUTE TO OUR LEGAL DEFENSE
All unused funds will be donated to the Electronic Frontier Foundation (EFF).
LET OTHERS KNOW
You can press escape or click on the X to close this box.
Computer doesnt start
Posted 22 November 2008 - 07:29 AM
But after that, to make the fan spin for another instant, I need to "turn it off" again. Meaning, I need to hold the power button for some seconds as if i wanted to foce the computer off, even when it is already off. Otherwise, the fan doesnt react.
The LED in the motherboard is on, so it gets power.
The 4 pin power connectors of the psu are dead except for those short instants when the fan spins.
amd 64 3000+ processor. I hope you dont need the motherboard model (asus something) cause i dont know it and i cant see it now, and its nice to avoid unplugging everything to search for a label hehe
any hypothesis that fits the symptoms? how should I proceed, doctors?
thanks a lot!
BC AdBot (Login to Remove)
Posted 22 November 2008 - 08:07 AM
The purpose of this procedure is to bypass the motherboard to test the PSU.
Caution: This procedure will involve working with live 12VDC electrical potentials which if handled improperly may lead to electrical shock. Proper precautions should also be taken to prevent electrostatic discharges (ESDs) within the case of the computer. For safety purposes please follow the instructions step by step.
First, shutdown your computer. Then unplug the power cable going into your computer.
Once you have opened the case, touch the metal of the case to discharge any static electricity.
The connector of the PSU which connects to the motherboard is readily recognizable by the number of wires in the bundle. To disconnect it you will need to press on the plastic clip to disengage it and then pull the connector up and away from the motherboard. Please take notice of the location of the locking tab and the notch on the socket of the motherboard, this will only connect one way as it is keyed. This wire bundle will have a memory of the way it has been installed and will want to bend back that direction, you may have to play around with it to find a position that the connector will stay in the same position while you run the test.
From the top left to right the pins are 13-24, the bottom from left to right are 1-12.
Please notice that there are PSUs with 24 pin and 20 pin connectors, the location of the green wire in the 24 pin connector is #16, and the green wire in the 20 pin connector is #14. If you look at the connector with socket side facing you and the clip on the top the number one pin will be on the bottom left corner. This makes the pin out for the 24 pin connector from left to right 13-24 on top, and 1-12 on the bottom. The pin out for the 20 pin connector from left to right is 11-20 on top , and 1-10 on the bottom. If you look at the connectors you notice that these are sockets that fit over the pins on the motherboard where the PSU cable attaches, this is where you will place the jumper. For a jumper you will need a piece of solid wire about the size of a paper clip (20-22 awg), preferably a wire with insulation. It will need to be large enough to fit firmly into the socket so that it will not need to be held in place while testing. You are at risk of electrical shock if you are holding the jumper when you power up the PSU. Insert one end of the jumper into the socket of the Green wire, and insert the other end into the socket of any Black wire.
Once the jumper is in place plug the cord back in. If the PSU is working properly the case fans, optical drives, hdds, and LEDs should power up and remain on. I would suggest that you not leave this connected any longer than is necessary for safety purposes.
To reconnect the 20/4 pin connector unplug the power cord, remove the jumper, and reconnect the connector. Take a moment at this time to make sure that nothing has been dislodged inside the case.
Systems Administrator, Windows Server 2008R2, Windows Server 2012
Certified CompTia Network +, A +
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users